Turbos

Ported shroud compressor housing for T3/T4E 60 trim with ported shroud (anti-surge machining) 0.60 A/R with 4" inlet and 2" outlet (T04E frame size).

Quick connect fitting Male 3/8" size to -6 AN male. Allows ease of transition from -6 AN to the newer O-ringed squeeze and release type fitting fou...

Quick connect fitting Male 5/16" size to -6 AN male. Allows ease of transition from -6 AN to the newer O-ringed squeeze and release type fitting fo...

Coolant (rear) line assembly for a Garrett GT or GTX series upgrade turbo on the Evo X (and Evo 8 / Evo 9). An excellent rear coolant line solution...

Fitting, -6AN (flare) female to -4AN (flare) male. Used to convert a -6AN male to -4AN male

SPECIAL RESTRICTED - Banjo Bolt for low profile oil feed line on GT and GTX Ball Bearing turbochargers. Optional (not required) 3 crush washers.CRU...

95mm Retaining Clip Holds Chra To Compressor Housing On All Bearing Turbos Between GT2554R To GT3582R. Applicable Garrett P/N's: 400589-0375

Rod Extension kit for internal wastegate actuator, (1)coupler, (2) nuts, (1) threaded rod 2" long.

RUBBER O-RING USED ON ADAPTER RING P/N: ATP-FLA-011

Stage 3, 350HP or 400HP (turbo choice dependent), GT28RS or GT2876R, dual ball bearing kit. All hardware with internally wastegated setup.

Stage 3, 450HP or 500HP (turbo choice dependent), GT3071R or GT3076R, dual ball bearing kit. All hardware with new 38mm wastegate. Features 3" Garr...

SFI Certified - Garrett GEN2 GTX5533R (88mm) dual ball bearing turbocharger (turbine housing sold separately). Designed for race classes limited to...

SHORT VERSION! No cutting or trimming before welding!Short Transition (Formed) stainless 3" OD to 3.5" OD, overall length 1.2" (30mm) no flange att...

Short Transition (Formed) stainless 3" OD to 4" OD, overall length 1.8" (45mm) no flange attached for welding to both sides, 76mm to 102mm

GT3071R Turbo kit, Volvo C30 T5 engine, 450+ HP capable, Ultra-responsive Garrett dual ball bearing GT3071R, 44mm Tial Wastegate, 3" stainless down...

SPACER PLATE, 3/16" BETWEEN BOLT ON GT TURBO AND UP-PIPE. RARELY REQUIRED (USED LESS THAN 1% OF THE TIME) BUT SUPPLIED IN EVERY ATP SUBARU BOLT-ON ...

Special Bolt to Plug the Speed Sensor Port on the Garrett Compressor Housing

Backplate Adapter Ring for Garrett EVO X Compressor Housing; GT3076R Model.

Special transition, formed tube, 3" round to oval, specific version made to work with flapper flange: ATP-FLS-067 and fits together just like shown...

Replacement Kit From Tial: Turbine Housing Clamp and Bolt Kit - For Tial stainless V-band housings for GT28/GT30/GT35. 2 x Half Moon Clamps from T...

Special turbine housing, T25 Inlet, GT28 Style 5 bolt outlet, and cast 44mm flanged External wastegate port. Available for Garrett series GT28, GTX...

Special V-band Clamp from ATP FSI/TSI Stock location kit (manifold to turbo connection)

SPECIAL-ACTUATOR-EVOX-STOCKLOC-GT-GTX for factory style comp hsg (w/ 3 bolt inlet)

Garrett GTX2863R dual ball bearing direct drop-in turbo for the Nissan SR20DET with a .64 A/R T25 internal wastegate turbine housing. Quick spoolin...

Garrett GTX2863R dual ball bearing direct drop-in turbo for the Nissan SR20DET with a .86 A/R T25 internal wastegate turbine housing. Quick spoolin...

New SRT-4 Cast Turbo Manifold. T3 Inlet flange. This new unit supports well over 400 wheel horsepower, and has external wastegate port pre-cast. Ma...

SRT4 / SRT-4 Oil Feed Fitting, Engine Block side to -4 AN MaleScrews into the engine block and allows you to screw the end of any -4 AN steel braid...

ATP turbo kit for the SRT-4, 400HP, Garrett T3/T4 with Tial 38mm wastegate and all hardware shown. Choice of Garrett T3/T4E 57 trim/Stage III or T...

SRT-4 Stage 3 Kit. 450 or 500HP (turbo choice dependent), GT3071R or GT3076R. Dual ball bearing kit, all hardware with new 44mm wastegate. Features...

Transition 2" to 2.5" (51mm to 63mm) Outer diameter to weld to, Stainless Steel 304, 2" OD to 2.5" OD, Overall Length is 1.2" (32mm).

Stainless steel coupler. 2" OD with beaded lips for clamping. AOL is 2-3/4". Use for hose extension or weld and add hose tee.

Stainless coupler, 2.5" OD with beaded lips for clamping. AOL is 2-3/4". Use for hose extension or weld and add hose tee.

ATP stainless steel v-band turbine inlet flange (exhaust / turbo manifold side). Compatible with Garrett undivided V-Band Inlet and Outlet Ni-Resi...

304 Stainless Steel CNC Machined weld flange for T25, GT25, T28 turbine inlet WITH Tapped holes (M8 x 1.25 threads). 1/2" thick prevents warping wi...

304 Stainless Steel CNC Machined weld flange for T3 turbine inlet WITH Tapped holes. 1/2" thick prevents warping with high heat. Bolt pattern: 3.37...

STAINLESS STEEL, Machined weld flange for T04 turbine inlet. 1/2" thick prevents warping with high heat. Bolt pattern: 3.250" x 2.750". The Flange ...

WIDE VERSION OF ATP-FLS-088 FOR USE WITH SPECIAL HSG-T25-EWG WITH GT35R. Stainless Stee Discharge Flange, CNC machined, for GT25R/GT28R/28RS and GT...

Compressor housing for Garrett GT4202(Both ball bearing and journal bearing versions) with 102mm 53 trim wheel (compatible turbos GT4202R/GT42RS/GT...

Compressor housing for Garrett GT4294 (Both ball bearing and journal bearing versions) with 94mm 56 trim wheel (compatible turbos GT42R/GT4294R/GT4...

Compressor housing for GT2860RS with 60mm 62 trim wheel, COMPRESSOR HSG .60 A/R, T04B style with 3" inlet and 2" outlet Applicable Garrett P/N's: ...

PRODUCT DESCRIPTION: Compressor housing for GT2871R with 71mm 56 trim wheel, COMPRESSOR HSG .60 A/R, T04B style with 3" inlet and 2" outlet, CAN AL...

Compressor housing for GT3076R 700382-5012 (or CHRA 700177-5007) with 76mm 56 trim wheel, COMPRESSOR HSG .60 A/R, T04E style with 4" inlet and 2" o...

Garrett's new compressor housing for GT3582R with "cast-in" ported shroud (anti-surge) 0.70 A/R with 4" inlet and 2.5" outlet (T04S frame size). Ap...

Standard T04S Frame Compressor housing for GTW3884R-67MM w/4" inlet and cast-in Anti-surge.

CNC Machined 4 bolt flange for GT/T3 turbine without internal wastegate. Machined with 3" inner diameter for 3" Downpipe use. * This flange is used...

HKS SSQ Steel Modular Weld-On Flange Kit. Includes Steel weld- on section and twist on top. Requires welding to mount to steel piping.

New CNC Machined weld flange for T3 turbine inlet divided WITH Tapped holes. 1/2" thick prevents warping with high heat. Bolt pattern: 3.375" x 1.7...