K Series K24A

K-Tuned AC & PS Eliminator Pulley Kit - K20/K24   Applications: Fits all K20 and K24 enginesNote:* This kit deletes both A/C and P/S, there is ...

The auto tensioner is replacement for the OEM unit. It mounts on the water pump and is designed to ensure proper belt tension at all times. Us...

*Fits both k20 and k24 applications* The K-Tuned Big Tube Swap Header was designed for more aggressive K-Swap cars with modified naturally aspirat...

Applications: K20 and K24A engines. Note:* K24 bracket is based off the CRV bracket (11910-PPA-000) and will only fit applications using the si...

K-Tuned Billet Oil Cap is not just specific to K-Series engines but will fit all Honda motors.  The K-Tuned Billet Oil Cap combines simple yet cla...

The idea of re-usable oil filter has been used in many forms of racing for several years now, but surprisingly, there were limited options availabl...

The K-Tuned Billet Shifter Base Plate is designed to install K-Tuned Accord Shifter or OEM Accord Shifter in EF/EG/EK/DA/DC2. This setup is prefer...

Application EK / DC2 with full radiators. Included are two lower rad brackets with well nuts. Simply drill two .5" holes and insert well nuts. Th...

CAI Pipe is 3.5"3.5" Short Ram Intake can reuse their filter. If you have the V-Stack you will need to order a 3.5" Air Filter. Cold Air Intake U...

 This fuel line kit is designed to work with an Inline fuel filter and our K-Tuned center feed fuel rail.  The kit includes our pre-assembled fu...

For our K-Tuned Intake Manifold project we partnered up with a long time friend and owner of Magnus Motorsports to design a performance intake mani...

K-Tuned has designed a one piece fitting that uses the existing center port on our rail to properly mount the fuel gauge in the center of our rail ...

On The K-Tuned Fuel Rail there is a custom center port for a gauge or center feed fuel lines.  Application:  K-Tuned Fuel rails

The K-Tuned Slave Cylinder is a great upgrade for those wanting to replace leaking or worn out OEM units. Many new K-Series cars (05-06 RSX, 06+ Ci...

Since releasing our original K-Tuned Coil Pack Cover several years ago we have seen a lot of replicas pop up. I guess we must have done something r...

Applications: All K-series engines Except K24Z-Series The K-Tuned Water Pump Block Off Plate system was designed to setup a K-series engine to use...

Replaced the old perished rubber hose with this brand spanking, reinforced silicone version! Looks good - fits good - works good - It's Good!  

This simple one wire sensor is needed on all K-swapped EF, EG, EK and DC2 chassis. It allows the coolant temperature reading to be properly disp...

The OEM RSX fan switch is used to control the rad fan on your K-swapped vehicle. The sensor fits in the RSX or EP3 radiator, the K-Tuned Swivel Nec...

Applications:  K-Tuned Billet Dip Stick (All Models) Note:  Our retention spring kit is designed for high horsepower k-Series cars running ou...

Don't get caught without an extra belt at the track. The K-Tuned belts are custom made to our specs. They are designed to be stronger and more dura...

These RSX specific fuel fittings are designed to work with our K-Tuned fuel rail and the existing OEM RSX fuel lines. They will also fit any rail w...

K-Tuned Electric Water Pump Kit - K Series B/D Alternator Applications: All K-series engines except K24Z and K24Y Series Engines with D/B Series Al...

K-Tuned Purge port plug is a simple and clean design to eliminate Purge ports on OEM and aftermarket throttle bodies. K-Tuned's billet plug is mad...

The K-Tuned 30 micron Inline fuel filter can be used universally. Can be disassembled for cleaning which is recommended every year depending on ho...

Our ground wire kit includes two 11" long ground wires. These are great upgrade for old corroded and worn grounds. You want to run one from transmi...

The K-Tuned 8th Gen Civic SI Header was specifically designed to optimize the performance and power output of the K20Z3 engine that is found in ...

The K-Tuned 8th Gen Civic SI Header was specifically designed to optimize the performance and power output of the K24 engine. The header was develo...

The K-Tuned 8th Gen Civic SI Header was specifically designed to optimize the performance and power output of the K20Z3 engine that is found in ...

Applications: All K-series engines The K-Tuned heater hose delete cap is used to block off any unused 5/8 diameter coolant ports. They come in han...

Applications: K-series cylinder heads (w/ heater hose fitting beside the header) Some of you may be interested in deleting the heater hoses and he...

Design specifically for the new K-tuned high flow fuel filters.

Removing the IACV from the throttlebody for cleaning used to be a real pain because it is held in place from the factory with tamper proof bolts.  ...

Applications: All K-series engines The K-Tuned Idle Air Assist Delete Kit will help clean up the overall look of any K-series engine by removing ...

Application: K-Series and OBD2 D/B-Series Temp Sensors The intake temp sensor adapter is a great option for boosted cars where the rubber grommet j...

The K24 Intake Manifold Adapter is a simple and easy way to install K20 style manifold on K24 heads. The recirculation fitting on K24s is typicall...

K-Tuned kits will allow you to build an intake system that will perfectly match your setup. They are available in both Short Ram or Cold Air config...

Application: All K-series engines Note:* Does NOT fit K24Z-Series* Must drill out mounting bolt passages in alternator to allow for upgraded hardwa...

Applications:  88-05 Civic EF, EG, EK, EP. EM 90-01 Integra DA, DC2 02-06 RSX DC5 Note:* Works on Type S or Aftermarket or JDM Brackets (Throttle w...

Applications: All K-series engines Replace the ugly rubber brake booster hose on your K-swap with our 8AN black braided line. This line not only l...

This complete kit is designed to work with an Inline fuel filter and our K-Tuned center feed fuel rail. This is a complete K-swap fuel system, whic...

Finally a good intake system for your K-Series swapped car, this intake is designed to fit engines that are using the original intake manifold. Unl...

We stepped into the wiring market for a reason. To release what we feel is the highest quality and easiest to install conversion harness available...

K-Tuned stepped into the wiring market for a reason. To release what they feel is the highest quality and easiest to install conversion harness av...

K-Tuned stepped into the wiring market for a reason. To release what they feel is the highest quality and easiest to install conversion harness av...