FuelTech

The FT600 Connector Kit is recommended for those who have upgraded to the FT600 ECU and want to modify their existing harness for the new FT600 con...

Molex 4 pin terminating resistor. Plug and play with FuelTech harness connections for CAN A devices.

FT Dial Board

FEATURESThe FT Dual Power Driver has two half bridge outputs that allows the activation of up to 25A current. With two half bridge outputs the DPD ...

Bracket kit designed to mount (4) FuelTech CDI Racing Ignition Coils Made from lightweight billet aluminum, only 13.1 oz Includes (4) 1/4” socket ...

Perfect mounting solution for your FT350/FT400/FT500 ECU.Modifications are required to fit specific vehicle.Approximate Dimensions: 18" x 12"

Perfect mounting solution for your FT600 ECU.Modifications are required to fit specific vehicle. Panels do not come trimmed down or with a carbon f...

Simplify installation of your FT450 or FT550 with this steering column mounting bracket.Size: 1.250"

Simplify installation of your FT600 with this steering column mounting bracket.Size: 1.250"

Simplify installation of your FT600 with this weld-on mounting kit.

Simplify installation of your FTSPARK with our chassis mounting bracket.Available sizes: 1.375", 1.500" and 1.625

4 channel conditioner for Type K thermocouples with CAN communication for PowerFT ECU's.FEATURES The FuelTech EGT-4 CAN is compatible with any type...

Typically used to monitor fuel, oil, and wastegate pressure.TECHNICAL DESCRIPTION Output: 0.5-4.5V Supply: 5V Range: 0-300 psi Thread size: 1/8" NP...

Typically used to monitor transmission, converter, clutch, and mechanical fuel pressure. Output: 0.5-4.5V Supply: 5V Range: 0-500 psi Thread size: ...

TECHNICAL DESCRIPTION Output: 0.5-4.5V Supply: 5V Range: 0-1500 psi Thread size: 1/8" NPT Connector Pinout: A - Ground B - 5V C - Signal SPECSPerfo...

Typically used for wheelie bar load cells.TECHNICAL DESCRIPTION Output: 0.5-4.5V Supply: 5V Range: 0-3000 psi Thread size: 1/8" NPT Connector Pinou...

This sensor is needed if you are exceeding the limit of your internal map sensor on your ECU or want to run an external map sensor on your setup. R...

Davis Technologies sensors are extremely high quality Hall Effect type, capable of measuring speeds up to 15 KHz. These sensors are triggered by fe...

Compatible with the following ECUs:FT600 / FT550 / FT500 / FT500LITE / FT450

Typically used to monitor fuel, oil, and wastegate pressure. Note: Generic pictures used.  

Pressure Sensor/Pan Vacuum Sensor Plug Kit

Compatible with WB-O2 Nano and the new NanoPRO.For use with the Bosch LSU4.2 O2 sensor.Length:2m (6.5ft) - Recommended size for most applications.

Nylon hose for MAP Sensor 4mm ID for vacuum/pressure hose Available in 10ft or 20ft To use with any FuelTech ECU or FuelTech BoostController

The FuelTech PRO600 V8 plug and play harness is the best link between your FT600 ECU and V8 engine. It comes pre-terminated to suit a V8 engine wit...

Can be used to read engine RPM or crank triggers. Can also be used to read wheel speed, gearbox speed, etc. with proper trigger wheel.Connector Pin...

Used to freeze the stock MAP / MAF signal when it reaches a certain value, preventing the sensor from sending a value that is out of range for the ...

Hall Effect Cam Sync Sensor w/ LED.This sensor is used with our BBC 1" Raised Cam Sync mounting bracket.

Hall effect variant of the common 3/4-16" thread crank sensor for flying magnet crank triggers.DOES NOT work with toothed ferrous metal trigger whe...

TECHNICAL DESCRIPTION Output: 1-5V Supply: 12V Range: 0-10 bar Thread size: 1/8" NPT Connector Pinout: 1 - Signal 2 - Ground 3 - 12V

Racepak’s 8-magnet driveshaft split collars are used in conjunction with our driveshaft sensor. These collars will pick up driveshaft RPM sooner th...

Racepak’s 8-magnet driveshaft split collars are used in conjunction with our driveshaft sensor. These collars will pick up driveshaft RPM sooner th...

FuelTech's billet remote pressure sensor mounting block is the perfect solution to mount your pressure sensors in one common place, Each port is in...

Thermocouple Exposed TipThe new FuelTech Thermocouple with Exposed Tip offers faster and more accurate temperature reading for exhaust gases.The ex...

Thermocouple Exposed TipThe new FuelTech Thermocouple with Exposed Tip offers faster and more accurate temperature reading for exhaust gases.The ex...

Thermocouple Exposed TipThe new FuelTech Thermocouple with Exposed Tip offers faster and more accurate temperature reading for exhaust gases.The ex...

Thermocouple Exposed TipThe new FuelTech Thermocouple with Exposed Tip offers faster and more accurate temperature reading for exhaust gases.The ex...

Thermocouple Exposed TipThe new FuelTech Thermocouple with Exposed Tip offers faster and more accurate temperature reading for exhaust gases.The ex...

Thermocouple Exposed TipThe new FuelTech Thermocouple with Exposed Tip offers faster and more accurate temperature reading for exhaust gases.The ex...

Fits most aftermarket throttle bodies that accept a "Ford" style throttle position sensor. It is Fitted with a 3 way GM metri-pack style connector....

Obtain vital data in order to determine whether the turbo is operating within its compressor map and at its highest efficiency. By inputting blade ...

The FTSPARK Connector Kit is recommended for those who want to build their own custom FTSPARK harness.Kit includes: (1) FTSPARK Connector (40) FTSP...